manualshive.com logo in svg

Toyota AVALON 2005, Operating Manual

The Toyota AVALON 2005 Pocket Reference Manual is an essential companion for every Avalon owner. This comprehensive manual provides detailed information on maintenance, troubleshooting, and operating instructions. Download your free copy now from manualshive.com and have this valuable manual at your fingertips whenever you need it.

Share
Download
background image

’05 MATRIX_U (L/O 0409)

222

2005 MATRIX from Sep. ’04 Prod. (OM12892U)

When restarting out after parking on a
slope:

1. With the transmission in “P” position

(automatic) or the clutch pedal de-
pressed (manual), start the engine.
(With an automatic transmission, be
sure to keep the brake pedal de-
pressed.)

2. Shift into gear.

3. Release the parking brake (also foot

brake on automatic transmission ve-
hicles) and slowly pull or back away
from the wheel blocks. Stop and apply
your brakes.

4. Have someone retrieve the blocks.

CAUTION

Do not exceed 72 km/h (45 mph) or
the posted towing speed limit,
whichever is lower. Because insta-
bility (swaying) of a towing vehicle-
trailer combination usually in-
creases as the speed increases, ex-
ceeding 72 km/h (45 mph) may
cause loss of control.

Slow down and downshift before
descending steep or long downhill
grades. Do not make sudden down-
shifts.

Avoid holding the brake pedal down
too long or too frequently. This
could cause the brakes to overheat
and result in reduced braking effi-
ciency.

Improving fuel economy is easy—just take
it easy. It will help make your vehicle last
longer, too. Here are some specific tips
on how to save money on both fuel and
repairs:

Keep your tires inflated at the cor-
rect pressure. Underinflation causes
tire wear and wastes fuel. See page
278 in Section 7- 2 for instructions.

Do not carry unneeded weight in
your vehicle. Excess weight puts a
heavier load on the engine, causing
greater fuel consumption.

Avoid lengthy warm- up idling. Once
the engine is running smoothly, begin
driving—but gently. Remember, howev-
er, that on cold winter days this may
take a little longer.

Keep the automatic transmission
overdrive turned on when engine
braking is not required. Driving with
the overdrive off will reduce the fuel
economy. (For details, see “Automatic
transmission” on page 119 in Section
1- 7.)

Accelerate slowly and smoothly.
Avoid jackrabbit starts. Get into high
gear as quickly as possible.

How to save fuel and make
your vehicle last longer

Summary of Contents for AVALON 2005
































































































































































































































































































































Reviews:

No comments

Related manuals for AVALON 2005

B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
Renault Lodgy 2017 Driver'S Handbook Manual preview
Lodgy 2017
Brand: Renault Pages: 238
Honda Fit LX 2015 Manual preview
Fit LX 2015
Brand: Honda Pages: 4
Pet Gear PG9300DR Instruction Manual preview
PG9300DR
Brand: Pet Gear Pages: 4
Kuda 293950 Installation Instruction preview
293950
Brand: Kuda Pages: 3
Bazooka UT6200 Troubleshooting Manual preview
UT6200
Brand: Bazooka Pages: 2
X-Armour XR-9500 Installation And Owner'S Manual preview
XR-9500
Brand: X-Armour Pages: 16
Vauxhall Signum Owner'S Manual preview
Signum
Brand: Vauxhall Pages: 310
Whispbar K536W Fitting Instructions Manual preview
K536W
Brand: Whispbar Pages: 17
Prorack K671 Fitting Instructions Manual preview
K671
Brand: Prorack Pages: 17
Ecco ED5101 Installation And Operating Instructions Manual preview
ED5101
Brand: Ecco Pages: 11
Oldsmobile 2003 Bravada Owner'S Manual preview
2003 Bravada
Brand: Oldsmobile Pages: 410
Axxess AXDSPX-GM31 Installation Instructions Manual preview
AXDSPX-GM31
Brand: Axxess Pages: 16
ZUS ZUHMBKBTV User Manual preview
ZUHMBKBTV
Brand: ZUS Pages: 15
Audi TT COUPE Service preview
TT COUPE
Brand: Audi Pages: 92
Toyota Prius V 2012 Hybrid Emergency Response Manual preview
Prius V 2012 Hybrid
Brand: Toyota Pages: 34
Dakota Digital VLC-41C Installation preview
VLC-41C
Brand: Dakota Digital Pages: 2
Fishbone Offroad FB22005 Installation Instructions preview
FB22005
Brand: Fishbone Offroad Pages: 3

Brands by name

Popular brands

Load more brands