manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 83

02_SEQUOIA_U (L/O 0108)

77

2002 MY SEQUOIA_U (OM34418U)

The  SRS  side  and  curtain  shield  airbag

system  may  not  activate  if  the  vehicle
is  subjected  to  a  collision  from  the  side

at  certain  angles,  or  a  collision  to  the

side  of  the  vehicle  body  other  than  the
passenger  compartment  as  shown  in

the  illustration.

The  SRS  side  and  curtain  shield  airbags

are  designed  to  inflate  when  the  passen-

ger  compartment  area  suffers  a  severe
impact  from  the  side.
For  the  safety  of  all  occupants,  always

wear  your  seat  belts  properly.

Collision  from  the  rear

Collision  from  the  front

Vehicle  rollover

The  SRS  side  and  curtain  shield  airbags

are  not  designed  to  inflate  if  the  ve-
hicle  is  involved  in  a  front  or  rear  colli-

sion,  if  it  rolls  over,  or  if  it  is  involved

in  a  low

−

speed  side  collision.

The  SRS  side  and  curtain  shield  airbag

system  consists  mainly  of  the  following
components,  and  their  locations  are  shown

in  the  illustration.

1. SRS  warning  light
2. Curtain  shield  airbag  modules

(airbag  and  inflator)

3. Side  airbag  modules 

(airbag  and  inflator)

4. Side  and  curtain  shield  airbag  sensors
5. Airbag  sensor  assembly

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands