Toyota 2002 Sequoia Owner'S Manual Download Page 105

Page: 105 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

Center

Left

The lower anchorages for the child re-

straint system interfaced with the

FMVSS225 specification are installed in
the center and left positions of the sec-

ond seats.

The anchorages are installed in the clear-
ance between the seat cushion and seat-

back for center and left positions of sec-

ond seats.
Child restraint system interfaced with the

FMVSS225 specification can be fixed with
these anchorages. In this case, it is not

necessary to fix the child restraint system

with a seat belt on the vehicle.

Cap

Covers

Type A

—Installation with child

restraint lower anchorages

(for second seats)

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands