Toyota 2002 Sequoia Owner'S Manual Download Page 240

Page: 240 / 329

02_SEQUOIA_U (L/O 0108)

234

2002 MY SEQUOIA_U (OM34418U)

CAUTION

The maximum gross trailer weight
(trailer weight plus cargo weight)

must never exceed the following.

Two

−

wheel drive models

2948 kg (6500 lb.)

Four

−

wheel drive models

2812 kg (6200 lb.)

If towing a trailer and cargo weigh-

ing over 907 kg (2000 lb.), it is
necessary to use a sway control

device with sufficient capacity. The

combination of the gross trailer
weight added to the total weight of

the vehicle, occupants and vehicle
cargo must never exceed a total of

5352  kg.  (11800  lb.)
Exceeding  the  maximum  weight  of
the  trailer,  the  vehicle,  or  the  ve-

hicle and trailer combination, can

cause an accident resulting in seri-
ous personal injuries.

Trailer hitch assemblies have differ-
ent weight capacities established by

the hitch manufacturer. Even though

the vehicle may be physically capa-
ble of towing a higher weight, the

operator must determine the maxi-

mum weight rating of the particular
hitch assembly and never exceed

the maximum weight rating speci-

fied for the trailer

−

hitch. Exceeding

the maximum weight rating set by

the trailer hitch manufacturer can

cause an accident resulting in seri-
ous personal injuries.

The gross vehicle weight must not
exceed the Gross Vehicle Weight

Rating (GVWR) indicated on the

Certification Label. The gross vehi-
cle weight is the sum of weights of

the unloaded vehicle, driver, pas-

sengers, luggage, hitch and trailer
tongue load. It also includes the

weight of any special equipment

installed on your vehicle.

The load on either the front or rear

axle resulting from distribution of

the gross vehicle weight on both
axles must not exceed the Gross

Axle Weight Rating (GAWR) listed
on the Certification Label.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands