manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 82

02_SEQUOIA_U (L/O 0108)

76

2002 MY SEQUOIA_U (OM34418U)

In  response  to  a  severe  side  impact,  the

SRS  side  and  curtain  shield  airbags  work

together  with  the  seat  belts  to  help  reduce
injury  by  inflating.  The  SRS  side  airbags

help  to  reduce  injuries  mainly  to  the  driv-

er’s  or  front  passenger’s  chest  and  the
SRS  curtain  shield  airbags  help  to  reduce

injuries  mainly  to  the  driver’s  or  front  pas-

senger’s  head.  The  SRS  side  and  curtain
shield  airbags  on  the  passenger  side  are

activated  even  with  no  passenger  in  the

front  seat.
Be  sure  to  wear  your  seat  belt  properly.
Your  vehicle  is  equipped  with  a  crash
sensing  and  diagnostic  module,  which  will

record  the  use  of  the  seat  belt  restraint

system  by  the  driver  and  front  passenger
when  the  SRS  side  and  curtain  shield  air-

bags  are  inflated.

CAUTION

SRS  side  and  curtain  shield  airbags
inflate  with  considerable  force.  To

avoid  potential  death  or  serious  injury

when  they  inflate,  the  driver  and  front
passenger  must:

!

Wear  their  seat  belts  properly.

!

Remain  properly  seated  with  their

back  upright  and  against  the  seat  at

all  times.

This  indicator  comes  on  when  the  igni-

tion  key  is  turned  to  the  “ON”  position.
It  goes  off  after  about  6  seconds.  This

means  the  SRS  side  and  curtain  shield

airbags  are  operating  properly.

This  warning  light  system  monitors  the

airbag  sensor  assembly,  front  airbag  sen-
sors,  side  and  curtain  shield  airbag  sensor

assemblies,  front  seat  belt  pretensioner

assemblies,  inflators,  warning  light,  inter-
connecting  wiring  and  power  sources.  (For

details,  see  “Service  reminder  indicators

and  warning  buzzers”  on  page  125  in  Sec-
tion  1

−

5.)

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands