manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 156

02_SEQUOIA_U (L/O 0108)

150

2002 MY SEQUOIA_U (OM34418U)

RESUMING  THE  PRESET  SPEED

If  the  preset  speed  is  cancelled  by  pulling

the  control  lever  or  by  depressing  the
brake  pedal  or  clutch  pedal,  pushing  the

lever  up  in  the  “RES/ACC”  direction  will

restore  the  speed  set  prior  to  cancellation.
However,  once  the  vehicle  speed  falls  be-

low  about  40  km/h  (25  mph),  the  preset
speed  will  not  be  resumed.

CRUISE  CONTROL  FAILURE  WARNING

If  the  “CRUISE”  indicator  light  in  the

instrument  cluster  flashes  when  using  the

cruise  control,  press  the  “CRUISE  ON

−

OFF”  button  to  turn  the  system  off  and

then  press  it  again  to  turn  it  on.
If  any  of  the  following  conditions  then  oc-
curs,  there  is  some  trouble  in  the  cruise

control  system.

!

The  indicator  light  does  not  come  on.

!

The  indicator  light  flashes  again.

!

The  indicator  light  goes  out  after  it

comes  on.

If  this  is  the  case,  contact  your  Toyota

dealer  and  have  your  vehicle  inspected.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands