manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 258

02_SEQUOIA_U (L/O 0108)

252

2002 MY SEQUOIA_U (OM34418U)

Type  C

3. Remove  the  wheel  ornament.

Pry  off  the  wheel  ornament,  using  the

beveled  end  of  the  wheel  nut  wrench  as
shown.
Type  A  only—To  protect  the  wheel  sur-
face,  place  sufficient  paper  or  cloth  be-

tween  the  wheel  and  wrench.

CAUTION

Do  not  try  to  pull  off  the  ornament  by
hand.  Take  due  care  in  handling  the

ornament  to  avoid  unexpected  person-

al  injury.

4. Loosen  all  the  wheel  nuts.

Always  loosen  the  wheel  nuts  before  rais-
ing  the  vehicle.
Turn  the  wheel  nuts  turn  counterclockwise
to  loosen.  To  get  maximum  leverage,  fit

the  wrench  to  the  nut  so  that  the  handle

is  on  the  right  side,  as  shown  above.
Grab  the  wrench  near  the  end  of  the  han-

dle  and  pull  up  on  the  handle.  Be  careful

that  the  wrench  does  not  slip  off  the  nut.
Do  not  remove  the  nuts  yet—just  unscrew

them  about  one

−

half  turn.

Front

Rear

5. Position  the  jack  at  the  correct  jack

point  as  shown.

Make  sure  the  jack  is  positioned  on  a

level  and  solid  place.
JACK  POINTS:

Front—Under  the  frame  side  rail
Rear—Under  the  rear  axle  housing

—Loosening  wheel  nuts

—Positioning  the  jack

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands