Toyota 2002 Sequoia Owner'S Manual Download Page 236

Page: 236 / 329

02_SEQUOIA_U (L/O 0108)

230

2002 MY SEQUOIA_U (OM34418U)

To drive down a long or steep hill,
reduce your speed and downshift.

Remember, if you ride the brakes

excessively, they may overheat and
not work properly.

Be careful when accelerating, up-

shifting, downshifting or braking on
a slippery surface. Sudden accelera-

tion or engine braking, could cause

the vehicle to spin or skid.

Do not drive in excess of the speed

limit. Even if the legal speed limit
permits it, do not drive over 140

km/h (85 mph) unless your vehicle

has high

−

speed capability tires.

Driving over 140 km/h (85 mph) may

result in tire failure, loss of control

and possible injury. Be sure to con-
sult a tire dealer to determine

whether the tires on your vehicle

are high

−

speed capability tires or

not before driving at such speeds.

Do not continue normal driving
when the brakes are wet. If they are

wet, your vehicle will require a

longer stopping distance, and it
may pull to one side when the

brakes are applied. Also, the park-

ing brake will not hold the vehicle
securely.

When driving your vehicle off

−

road, please

observe the following precautions to en-

sure your driving enjoyment and to help
prevent the closure of areas to off

−

road

vehicles.

a. Drive your vehicle only in areas where

off

−

road vehicles are permitted to trav-

el.

b. Respect private property. Get owner’s

permission before entering private prop-

erty.

c. Do not enter areas that are closed.

Honor gates, barriers and signs that re-

strict travel.

d. Stay on established roads. When condi-

tions are wet, driving techniques should
be changed or travel delayed to pre-

vent damage to roads.

For owners in U.S. mainland, Hawaii and

Puerto  Rico:
To  obtain  additional  information  pertaining
to  driving  your  vehicle  off

−

road, consult

the following organizations.

State and Local Parks and Recreation

Departments

State Motor Vehicle Bureau

Recreational Vehicle Clubs

Off

−

road driving precautions

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands