Toyota 2002 Sequoia Owner'S Manual Download Page 78

Page: 78 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

Never put a rear

−

facing child re-

straint system in the front passen-

ger seat because the force of the

rapid inflation of the front passen-
ger airbag can cause death or seri-

ous injury to the child.

Move seat fully back

A forward

−

facing child restraint sys-

tem should be allowed to be put on

the front passenger seat only when

it is unavoidable. Always move the
seat as far back as possible, be-

cause the force of the deploying

front passenger airbag could cause
death or serious injury to the child.

On vehicles with side airbags, do
not allow the child to lean against

the front door or around the front

door even if the child is seated in
the child restraint system. It is dan-

gerous if the side airbags inflate,

because the impact could cause
death or serious injury to the child.

For instructions concerning the

installation of a child restraint sys-
tem, see “Child restraint” on page

82 in this section.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands