manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 257

02_SEQUOIA_U (L/O 0108)

251

2002 MY SEQUOIA_U (OM34418U)

2. Insert  the  end  of  the  jack  handle  exten-

sion  into  the  lowering  screw  and  turn
it  counterclockwise  with  the  handle,

making  sure  the  handle  remains  firmly

fitted  onto  the  jack  handle  extension.

3. After  the  tire  is  lowered  completely  to

the  ground,  remove  the  holding  brack-
et.

When  storing  the  spare  tire,  put  it  in  place

with  the  outer  side  of  the  wheel  facing  up.
Then  secure  the  tire,  taking  care  that  the

tire  goes  straight  up  without  catching  on

any  other  part,  to  prevent  it  from  flying
forward  during  a  collision  or  sudden  brak-

ing.

2. Block  the  wheel  diagonally  opposite

the  flat  tire  to  keep  the  vehicle  from
rolling  when  it  is  jacked  up.

When  blocking  the  wheel,  place  a  wheel
block  from  the  front  for  the  front  wheels

or  from  the  rear  for  the  rear  wheels.

Type  A

Type  B

—Blocking  the  wheel

—Removing  wheel  ornament

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands