Toyota 2002 Sequoia Owner'S Manual Download Page 141

Page: 141 / 329

02_SEQUOIA_U (L/O 0108)

135

2002 MY SEQUOIA_U (OM34418U)

(d) Using engine braking

To use engine braking, you can downshift

the transmission as follows:

Push the overdrive switch. The “O/D

OFF” indicator light will come on and
the transmission will downshift to third

gear.

Shift into the “2” position. The trans-
mission will downshift to second gear

when the vehicle speed drops down to

or lower than the following speed, and
stronger engine braking will be en-

abled.

Two

−

wheel drive models

110 km/h (68 mph)

Four

−

wheel drive models

Front drive control lever in “H”

(2WD) or “H” (4WD)

110 km/h (68 mph)

Front drive control lever in “L4”

39 km/h (24 mph)

Shift into the “L” position. The trans-

mission will downshift to first gear

when the vehicle speed drops down to
or lower than the following speed, and

maximum engine braking will be en-

abled.

Two

−

wheel drive models

55 km/h (34 mph)

Four

−

wheel drive models

Front drive control lever in “H”

(2WD) or “H” (4WD)

55 km/h (34 mph)

Front drive control lever in “L4”

10 km/h (5 mph)

When the cruise control is being used,

even if you downshift the transmission by
pushing and releasing the overdrive

switch, engine braking will not be enabled
because the cruise control is not can-

celled.
For ways to decrease the vehicle speed,
see “Cruise control” on page 148 in this

section.

CAUTION

Be careful when downshifting on a
slippery

surface.

Abrupt

shifting

could cause the vehicle to spin or

skid.

(e) Using the “2” and “L”, positions

The “2” and “L” positions are used for

strong engine braking as described pre-

viously.
With the selector lever in “2” or “L”, you

can start the vehicle in motion as with the

lever in “D”.
With the selector lever in “2”, the vehicle

will  start  in  first  gear  and  automatically
shift  to  second  gear.
With  the  selector  lever  in  “L”,  the  trans-
mission  is  engaged  in  first  gear.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands