manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 150

02_SEQUOIA_U (L/O 0108)

144

2002 MY SEQUOIA_U (OM34418U)

When  the  traction  control  system  is  oper-

ating,  the  following  conditions  occur:

!

The  system  controls  the  spinning  of  the
4  wheels  (4WD  mode)  or  rear  wheels

(2WD  mode).  At  this  time,  the  slip  indi-

cator  light  blinks.

!

You  may  feel  vibration  or  noise  in  your

vehicle,  caused  by  operation  of  the
brakes.  This  indicates  the  system  is

functioning  properly.

The  slip  indicator  light  comes  on  for  a  few
seconds  when  the  ignition  key  is  turned

to  “ON”.  If  the  indicator  light  does  not

come  on  when  the  ignition  is  turned  on,
contact  your  Toyota  dealer.

“VSC/TRAC”  warning  light

This  light  warns  that  there  is  a  problem
somewhere  in  the  active  traction  control

system  or  the  vehicle  skid  control  system.
The  light  will  come  on  when  the  ignition

key  is  turned  to  “ON”  and  will  go  off  after

a  few  seconds.

The  brake  actuator  temperature  increases

during  continuous  operation  of  the  active

traction  control  system  or  vehicle  skid
control  system  such  as  on  slippery  roads.

If  the  brake  actuator  temperature  becomes

too  high  while  the  active  traction  control
system  or  vehicle  skid  control  system  is

operating,  a  buzzer  will  start  to  sound

intermittently  to  indicate  that  the  active
traction  control  system  can  no  longer  op-

erate.  In  this  case,  immediately  stop  your

vehicle  at  a  safe  place.
If  the  system  continues  to  operate,  the

buzzer  sound  changes  from  intermittent  to

continuous. 

(The 

continuous 

buzzer

sounds  for  about  3  seconds.)
At  the  time,  the  “VSC/TRAC”  warning  light
will  come  on  and  the  active  traction  con-

trol  system  temporarily  stops  operating  in

order  to  protect  the  brake  actuator.  (Al-
though  the  active  traction  control  system

does  not  operate,  there  is  no  problem  to

continue  your  driving.)  The  system  will  be
automatically  restored  after  a  short  time

and  the  warning  light  goes  out.
If  the  light  comes  on  while  driving,  the

active  traction  control  system  does  not

work.  However,  as  conventional  braking
operates  when  applied,  there  is  no  prob-

lem  to  continue  your  driving.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands