manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 134

02_SEQUOIA_U (L/O 0108)

128

2002 MY SEQUOIA_U (OM34418U)

Even  if  the  abnormality  of  the  electronic

throttle  control  system  is  corrected  during

low  speed  driving,  the  system  may  not  be
recovered  until  the  engine  is  stopped  and

the  ignition  key  is  turned  to  “ACC”  or

“LOCK”  position.

CAUTION

Be  especially  careful  to  prevent  erro-
neous  pedal  operation.

Emissions  inspection  and  maintenance
(I/M)  programs

We  recommend  you  to  contact  your

Toyota  dealer  to  check  your  vehicle’s
emission 

control 

system 

and 

OBD

(On

−

Board  Diagnostics)  system  before

taking  your  vehicle  for  a  state  emission
inspection.
For  details,  see  “Emissions  Inspection  and
Maintenance  (I/M)  programs”  on  page  276

in  Section  6.

(f) Low  Fuel  Level  Warning  Light

This  light  comes  on  when  the  fuel  level

in  the  tank  becomes  nearly  empty.  Fill  up
the  tank  as  soon  as  possible.
On  inclines  or  curves,  due  to  the  move-
ment  of  fuel  in  the  tank,  the  low  fuel  level

warning  light  may  come  on  earlier  than

usual.

(g) “ABS”  Warning  Light

The  light  comes  on  when  the  ignition  key
is  turned  to  the  “ON”  position.  If  the  anti

−

lock  brake  system  works  properly,  the

light  turns  off  after  a  few  seconds.  There-
after,  if  the  system  malfunctions,  the  light

comes  on  again.
When  the  “ABS”  warning  light  is  on  (and
the  brake  system  warning  light  is  off),  the

anti

−

lock  brake  system,  the  traction  con-

trol  system  (two

−

wheel  drive  vehicles),  the

active  traction  control  system  (four

−

wheel

drive  vehicles)  and  the  vehicle  skid  con-
trol  system  do  not  operate,  but  the  brake

system  still  operates  conventionally.
When  the  “ABS”  warning  light  is  on  (and
the  brake  system  warning  light  is  off),  the

anti

−

lock  brake  system  does  not  operate

so  that  the  wheels  could  lock  up  during
a  sudden  braking  or  braking  on  slippery

road  surfaces.

If  either  of  the  following  conditions

occurs,  this  indicates  a  malfunction

somewhere  in  the  parts  monitored  by
the  warning  light  system.  Contact  your

Toyota  dealer  as  soon  as  possible  to

service  the  vehicle.

!

The  light  does  not  come  on  when  the

ignition  key  is  turned  to  the  “ON”  posi-

tion,  or  remains  on.

!

The  light  comes  on  while  you  are  dri-

ving.

A  warning  light  turning  on  briefly  during

operation  does  not  indicate  a  problem.

CAUTION

If  the  “ABS”  warning  light  remains  on
together  with  the  brake  system  warn-

ing  light,  immediately  stop  your  ve-

hicle  at  a  safe  place  and  contact  your
Toyota  dealer.
In  this  case,  not  only  the  anti

−

lock

brake  system  will  fail  but  also  the
vehicle  will  become  extremely  unsta-

ble  during  braking.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands