manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 154

02_SEQUOIA_U (L/O 0108)

148

2002 MY SEQUOIA_U (OM34418U)

CAUTION

Before  driving,  be  sure  the  parking
brake  is  fully  released  and  the  park-

ing  brake  reminder  light  is  off.

The  cruise  control  allows  you  to  cruise

the  vehicle  at  a  desired  speed  over  40

km/h  (25  mph)  even  with  your  foot  off
the  accelerator  pedal.

Your  cruising  speed  can  be  maintained  up

or  down  grades  within  the  limits  of  engine
performance,  although  a  slight  speed

change  may  occur  when  driving  up  or

down  the  grades.  On  steeper  hills,  a
greater  speed  change  will  occur  so  it  is

better  to  drive  without  the  cruise  control.

CAUTION

!

To  help  maintain  maximum  control
of  your  vehicle,  do  not  use  the

cruise  control  when  driving  in

heavy  or  varying  traffic,  or  on  slip-
pery  (rainy,  icy  or  snow

−

covered)  or

winding  roads.

!

Avoid  vehicle  speed  increases  when
driving  downhill.  If  the  vehicle

speed  is  too  fast  in  relation  to  the

cruise  control  set  speed,  cancel  the
cruise  control  then  downshift  the

transmission  to  use  engine  braking

to  slow  down.

TURNING  ON  THE  SYSTEM

To  operate  the  cruise  control,  press  the
“CRUISE  ON

−

OFF”  button.  This  turns  the

system  on.  The  indicator  light  in  the
instrument  panel  shows  that  you  can  now

set  the  vehicle  at  a  desired  cruising

speed.  Another  press  will  turn  the  system
completely  off.

CAUTION

To  avoid  accidental  cruise  control  en-
gagement,  keep  the  “CRUISE  ON

−

OFF”  switch  off  when  not  using  the

cruise  control.

Cruise  control

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands