Toyota 2002 Sequoia Owner'S Manual Download Page 129

Page: 129 / 329

02_SEQUOIA_U (L/O 0108)

123

2002 MY SEQUOIA_U (OM34418U)

Idling for a long period with the air

conditioning on in stop

−

and

−

go traffic.

Towing a trailer.

NOTICE

Do not remove the thermostat in
the engine cooling system as this

may cause the engine to overheat.

The thermostat is designed to con-
trol the flow of coolant to keep the

temperature of the engine within

the specified operating range.

Do not continue driving with an

overheated engine. See “If your ve-

hicle overheats” in Section 4.

Normal

driving

Idling

The oil pressure gauge indicates engine

oil pressure when the ignition switch is
on. Check it while driving to make sure

that the needle is in the proper range.

If the oil pressure should stay below the

normal range, pull off the road to a safe

place and stop the engine immediately.
Call a Toyota dealer or qualified repair

shop  for  assistance.
Oil  pressure  may  not  build  up  when  the
oil  level  is  too  low.  The  oil  pressure

gauge is not designed to indicate oil level,

and the oil level must be checked using
the level dipstick.

NOTICE

Do not drive the vehicle with the oil
pressure below the normal range until

the cause is fixed—it may ruin the

engine.

Oil pressure gauge

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands