manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 106

02_SEQUOIA_U (L/O 0108)

100

2002 MY SEQUOIA_U (OM34418U)

Cap

Covers

Type  B

CHILD 

RESTRAINT 

SYSTEM

INSTALLATION
Type  A—

1. Turn  up  the  covers  for  left  lower

anchorage  on  the  center  position  of
the  seats  anchorages  on  the  left  side

position  of  the  seats,  and  remove

the  cap  for  the  right  lower  anchor-
age  of  the  center  position  of  the

seat  as  shown  in  the  illustration.

2. Widen  the  clearance  between  the

seat  cushion  and  seatback  a  little

and  confirm  the  position  of  the  low-

er  anchorages  below  the  tag  and  cap
in  the  seat  cushion.

3. Latch  the  hooks  of  lower  straps  onto

the  anchorages  and  tighten  the  lower

straps.

Type  B—

1. Turn  up  the  covers  for  left  lower

anchorage  on  the  center  position  of
the  seats  anchorages  on  the  left  side

of  the  position  of  the  seat,  and  re-

move  the  cap  for  the  right  lower  an-
chorage  of  the  center  position  of  the

seat  as  shown  in  the  illustration.

2. Widen  the  clearance  between  the

seat  cushion  and  seatback  a  little

and  confirm  the  position  of  the  low-
er  anchorages  below  the  tag  in  the

seat  cushion.

3. Latch  the  buckles  onto  the  anchor-

ages.

If  your  child  restraint  system  has  a  top
strap,  it  should  be  anchored.  (For  the

installation  of  the  top  strap,  see  “—Using

a  top  strap”  on  page  95  in  this  section.)
For  the  installation  details,  refer  to  the

instruction  manual  equipped  with  each

product.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands