Toyota 2002 Sequoia Owner'S Manual Download Page 281

Page: 281 / 329

02_SEQUOIA_U (L/O 0108)

275

2002 MY SEQUOIA_U (OM34418U)

Battery condition

Check the battery condition by the indica-

tor color. See page 296 in Section 7

−

3 for

additional information.

Brake fluid level

Make sure the brake fluid level is correct.

See page 287 in Section 7

−

2 for addition-

al information.

Engine oil level

Check the level on the dipstick with the
engine turned off and the vehicle parked

on a level spot. See page 284 in Section

−

2 for additional information.

Power steering fluid level

Check the level through the reservoir. The

level should be in the “HOT” or “COLD”

range depending on the fluid temperature.
See page 287 in Section 7

−

2 for addition-

al information.

Exhaust system

If you notice any change in the sound of

the exhaust or smell exhaust fumes, have
the cause located and corrected immedi-

ately. (See “Engine exhaust cautions” on

page 217 in Section 2.)

Be on the alert for changes in perfor-

mance, sounds, and visual tip

−

offs that

indicate service is needed. Some impor-
tant clues are as follows:

Engine missing, stumbling, or pinging

Appreciable loss of power

Strange engine noises

A leak under the vehicle (however, wa-

ter dripping from the air conditioning

after use is normal.)

Change in exhaust sound (This may

indicate a dangerous carbon monoxide

leak. Drive with the windows open and
have the exhaust system checked im-

mediately.)

Flat

−

looking tire; excessive tire squeal

when cornering; uneven tire wear

Vehicle pulls to one side when driving

straight on a level road

Strange noises related to suspension
movement

Loss of brake effectiveness; spongy
feeling brake or clutch pedal; pedal al-

most touches floor; vehicle pulls to one

side when braking

Engine coolant temperature continually

higher than normal

Engine continually runs hot; oil pres-

sure gauge stays low.

If you notice any of these clues, take your
vehicle to your Toyota dealer as soon as

possible. It probably needs adjustment or

repair.

CAUTION

Do not continue driving with the ve-
hicle unchecked. It could result in se-

rious vehicle damage and possibly

personal injury.

Does your vehicle need

repairing?

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands