Toyota 2002 Sequoia Owner'S Manual Download Page 26

Page: 26 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

For vehicles sold in Canada

Operation is subject to the following two
conditions:
(1) this device may not cause interfer-

ence, and (2) this device must accept
any interference, including interference

that may cause undesired operation of

the device.

REPLACING THE BATTERY

For replacement, use a lithium battery

CR2016.

CAUTION

Special care should be taken that
small children do not swallow the re-

moved battery or components.

NOTICE

When replacing the transmitter bat-
tery, be careful not to lose the com-

ponents.

Replace only with the same or
equivalent type recommended by

the manufacturer.

Dispose of used batteries according

to the local laws.

Replace the battery by the following pro-

cedures:

1. Using a coin or equivalent, open the

transmitter case.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands