manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 56

02_SEQUOIA_U (L/O 0108)

50

2002 MY SEQUOIA_U (OM34418U)

3. To  stow  the  center  seat  belt,  pull  it

slightly  out  of  its  cover.  It  will  auto-
matically  roll  back  partway.  Roll  the

seat  belt  backwards  as  shown  above

and  insert  it  into  the  slot  of  its  cov-
er.  Make  sure  the  tabs  are  securely

locked  in  the  cover.

NOTICE

The  seat  belt  must  be  stowed  before
you  fold  the  seatback.

From  front

From  rear

REMOVING  THIRD  SEATS

1. Move  the  seat  to  the  rear

−

most  posi-

tion.  Lower  the  head  restraint  to  the
lowest  position.  Unlock  the  seatback

and  fold  it  down.

CAUTION

Make  sure  people  or  luggage  are
clear  from  the  seat.  Then,  hold  the

seat  and  slowly  move  it.  Otherwise,

people  may  be  injured  or  luggage
may  be  damaged,  if  the  seat  hits

them.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands