manualshive.com logo in svg

Toyota 2002 Sequoia, Owner'S Manual

Share
Download
Toyota 2002 Sequoia Owner'S Manual Download Page 297

02_SEQUOIA_U (L/O 0108)

291

2002 MY SEQUOIA_U (OM34418U)

To  equalize  the  wear  and  help  extend

tire  life,  Toyota  recommends  that  you

rotate  your  tires  according  to  the  main-
tenance  schedule.  (For  scheduled  main-

tenance  information,  please  refer  to  the

“Scheduled  Maintenance  Guide”  or
“Owner’s  Manual  Supplement”.)  Howev-

er,  the  most  appropriate  timing  for  tire

rotation  may  vary  according  to  your
driving  habits  and  road  surface  condi-

tions.

See  “If  you  have  a  flat  tire”  on  page  249
in  Section  4  for  tire  change  procedure.
When  rotating  tires,  check  for  uneven
wear  and  damage.  Abnormal  wear  is  usu-

ally  caused  by  incorrect  tire  pressure,  im-

proper  wheel  alignment,  out

−

of

−

balance

wheels,  or  severe  braking.

WHEN  TO  USE  SNOW  TIRES  OR

CHAINS
Snow  tires  or  chains  are  recommended
when  driving  on  snow  or  ice.

On  wet  or  dry  roads,  conventional  tires
provide  better  traction  than  snow  tires.

SNOW  TIRE  SELECTION
If  you  need  snow  tires,  select  the  same

size,  construction  and  load  capacity  as

the  original  tires  on  your  Toyota.

Do  not  use  tires  other  than  those  men-

tioned  above.  Do  not  install  studded  tires

without  first  checking  local  regulations  for
possible  restrictions.

SNOW  TIRE  INSTALLATION
Snow  tires  should  be  installed  on  all

wheels.

Installing  snow  tires  on  the  front  wheels

only  can  lead  to  an  excessive  difference

in  road  grip  capability  between  the  front
and  rear  tires  which  could  cause  loss  of

vehicle  control.
When  storing  removed  tires,  you  should

store  them  in  a  cool  dry  place.
Mark  the  direction  of  rotation  and  be  sure
to  install  them  in  the  same  direction  when

replacing.

CAUTION

#

Do  not  drive  with  the  snow  tires
incorrectly  inflated.

#

Never  drive  over  120  km/h  (75  mph)

with  any  type  of  snow  tires.

TIRE  CHAIN  SELECTION
Use  the  tire  chains  of  correct  size.
Regulations  regarding  the  use  of  tire

chains  vary  according  to  location  or
type  of  road,  so  always  check  them

before  installing  chains.
CHAIN  INSTALLATION
Install  the  chains  on  the  rear  tires  as

tightly  as  possible.  Do  not  use  tire
chains  on  the  front  tires.  Retighten

chains 

after 

driving 

0.5—1.0 

km

(1/4—1/2  mile).

When  installing  chains  on  your  tires,  care-

fully  follow  the  instructions  of  the  chain
manufacturer.
If  wheel  covers  are  used,  they  will  be
scratched  by  the  chain  band,  so  remove

the  covers  before  putting  on  the  chains.

Installing  snow  tires  and

chains

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands