Toyota 2002 Sequoia Owner'S Manual Download Page 104

Page: 104 / 329

02_SEQUOIA_U (L/O 0108)

2002 MY SEQUOIA_U (OM34418U)

TO USE THE ANCHORAGES:

1. Remove the head restraint.

2. Fix the child restraint system with

the seat belt.
Latch the hook onto the anchor

bracket and tighten the top strap.

For instructions to install the child re-

straint system, see “Child restraint” on

page 82 in this section.

CAUTION

Make sure the top strap is securely
latched, and check that the child re-

straint system is secure by pushing

and pulling it in different directions.

3. Replace the head restraint.

Summary of Contents for 2002 Sequoia










































































































































































































































































































































Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands

Toyota 2002 Sequoia, Owner'S Manual

Search results

Summary of Contents for 2002 Sequoia

Reviews:

Brands by name

Popular brands