manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 97 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 97

6

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

SCANNER

6 - 5

6.4

Description of Operation

6.4.1

Scanning operation

• Scanning an original on the original glass

The rotation of the scan motor (M1) is transmitted to the CIS unit through the timing belt to move the 
unit to the home position. The home position is detected when the actuator installed on the CIS case 
passes the CIS home position sensor (S1).

When the [START] button is pressed, the CIS unit starts scanning the original.

• Scanning an original on the ADF/RADF

The CIS unit (CIS) stops and stays at the shading position during the shading correction, and at the 
scanning position during the scanning operation.

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments