manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 104 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 104

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

SCANNER

6 - 12

6.6

Automatic Original Size Detection Circuit

This circuit detects the size of original (standard sizes only) using the reflection type photosensors 
arranged on the base frame of the scanner unit.

6.6.1

Principle of original size detection

Reflection type photosensors are placed on the base frame of the scanner unit as shown in the figure 
below. Each sensor consists of an infrared Light Emitting Diode (LED) on the light emitting side, and a 
phototransistor on the light receiving side.
When there is an original on the original glass, light beams from the LEDs are reflected by the original 
and led to the phototransistors. This means that the presence of the original is detected by the pres-
ence of reflection (when scanning black image).

 Fig. 6-7

Original

Original glass

[A4 Series]

[LT Series]

Original

Original glass

APS-3

APS-1

APS-2

APS-C

APS-R

APS-3

APS-2

APS-C

APS-R

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments