Toshiba e-studio 167 Service Manual Download Page 202

Page: 202 / 268

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 8

12.5 Auto-Toner Circuit

12.5.1

General description

1) Function of the auto-toner circuit

- Detects the toner density in the developer material, and supplies toner when the density is low-

ered to a certain level.

- Detects that there is no toner left in the cartridge (toner-empty detection).

2) The auto-toner circuit consists of the following:

- Auto-toner sensor:

Detects the toner density.

- Control section:

Controls the toner density so that the toner in the developer material is fixed to certain ratio.

- Toner motor:

Supplies toner to the developer material.

- Control panel:

Indicates toner-empty information.

- Recovered toner supply section:

The main motor supplies the recovered toner to the developer unit from the recovered toner sup-
ply mechanism.

Fig. 12-4

Toner

Developer material

Auto-toner sensor

Toner cartridge

Recovered toner

supply section

Temperature/humidity sensor

Toner
motor

Recovered

toner

Recovered toner

supply mechanism

Main

motor

A/D

converter

D/A

converter

ASIC

SoC

Flash ROM

Control panel

Control section

MAIN board

Developer unit

Control voltage signal

Toner density signal

"Toner Empty"

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 202 / 268

Search results

Summary of Contents for e-studio 167

Reviews: