Toshiba e-studio 167 Service Manual Download Page 105

Page: 105 / 268

e-STUDIO167/207/237

SCANNER

6 - 13

6.6.2

Process of detection of original size

1) When the equipment is in the original size detection mode, contact image sensor unit (CIS) is set at

its home position.

2) When the platen cover is opened, the sensors receive the light reflected from the original and if one

of the matrix conditions shown in 4) for original sizes are met, the size of the original is instantly
detected.

3) The output signal from each sensor is input to ASIC on the MAIN board to determine the size of the

original.

Fig. 6-8

MAIN board

APS-C

APS-3

APS-2

APS-R

ASIC

+5VAPS

+5V

+5VAPS

+5V

MAIN board

APS-C

APS-2

APS-3

APS-1

APS-R

ASIC

Reflection type
photosensor

[A4 Series]

[LT Series]

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 105 / 268

Search results

Summary of Contents for e-studio 167

Reviews: