Toshiba e-studio 167 Service Manual Download Page 14

Page: 14 / 268

e-STUDIO167/207/237

SPECIFICATIONS / ACCESSORIES / OPTIONS / SUPPLIES

1 - 6

1.3

Options

Notes:

• When the paper feed pedestal (KD-1022) or automatic duplexing unit (MD-0103) is installed,

the paper feed controller (GH-1060) is also required to be installed.

• The external keyboard (GJ-1040) is necessary for the installation of the fax kit (GD-1220/

1221) and the scanner upgrade kit (GA-1200).

Platen Cover

KA-1640PC/C

Automatic Document Feeder (ADF)

MR-2017/C

Reversing Automatic Document Feeder (RADF)

MR-3019/C

Paper Feed Unit (PFU)

MY-1027/C

Paper Feed Pedestal (PFP)

KD-1022/C

Paper Feed Controller (PFC)

GH-1060/C

Drawer Module

MY-1028/C

Automatic Duplexing Unit (ADU)

MD-0103/C

Fax Kit

GD-1220NA/EU/AU/TW/CN/KR
GD-1221NA/EU/AU/TW/CN/KR

External Keyboard

GJ-1040/C/EU/KR/TW

Network Printer Kit

GA-1190/C/KR/TW

Scanner Upgrade Kit

GA-1200/C/KR/TW

Operator’s manual pocket

KK-1660/C

Damp Heater

MF-1640U/E

Harness Kit

GQ-1130

Desk

MH-1640

08/06

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 14 / 268

Search results

Summary of Contents for e-studio 167

Reviews: