Toshiba e-studio 167 Service Manual Download Page 236

Page: 236 / 268

e-STUDIO167/207/237

FUSER / EXIT UNIT

13 - 20

[I]

Center thermistor / Side thermistor / Edge thermistor (THMS1/THMS2/THMS3)

(4) Take off each 1 pressure lever on both front

and rear sides.

Fig. 13-29

(5) Take off 2 bushings and then take off the

pressure roller while sliding the pressure
roller to the rear side.

Notes:

• Do not drop the pressure roller when you

lift it up because it is quite heavy.

• Be sure to install the pressure roller from

the rear side (pressure roller ground plate
side) in order not to deform the pressure
roller ground plate.

Fig. 13-30

(1) Take off the fuser roller.

P.13-18 "[G] Fuser roller"

(2) Remove each 1 screw of the thermistors,

and then take off each thermistor by releas-
ing its harness out of the harness clamp.

Fig. 13-31

Pressure lever

Pressure roller

Bushing

Pressure roller
ground plate

Bushing

Thermistor

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 236 / 268

Search results

Summary of Contents for e-studio 167

Reviews: