Toshiba e-studio 167 Service Manual Download Page 186

Page: 186 / 268

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 14

[H] Drum

[I]

Drum cleaning blade

(1) Take off the main charger.

P.11-12 "[D] Main charger"

(2) Rotate the lever while pushing its latch and

pull it out.

(3) Take off the drum.

Notes:

1. Be careful not to touch, spit or scratch the

drum surface.

2. Avoid direct light. Place the drum in a

dark place immediately after taking off.

3. Be careful not to touch or scratch the

edge of the cleaning blade.

Fig. 11-20

(1) Take off the drum.

P.11-14 "[H] Drum"

(2) Remove 2 screws and take off the drum

cleaning blade.

Note:

Be careful not to touch or scratch the edge of
the drum cleaning blade.

Fig. 11-21

Drum

Lever

Drum cleaning blade

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 186 / 268

Search results

Summary of Contents for e-studio 167

Reviews: