manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 207 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 207

12

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 13

[C] Filling developer unit with developer material

[D] Auto-toner sensor (S6)

(1) Rotate the gear on the rear side of the devel-

oper unit to the direction of the arrow while 
filling the developer unit with the developer 
material. Spread out the developer material 
over the developer sleeve.

• Attach the nozzle as required.

 Fig. 12-11

(1) Remove the developer material. 

 P.12-12 "[B] Developer material"

(2) Place the developer unit upside down.

Disconnect 1 connector, release 1 latch, and 
then rotate the auto toner sensor counter-
clockwise to take it off.

 Fig. 12-12

Lid

Nozzle

Connector

Auto toner sensor

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments