Toshiba e-studio 167 Service Manual Download Page 143

Page: 143 / 268

e-STUDIO167/207/237

DRIVE UNIT

9 - 9

(7) Take off the gear and timing belt from the

main motor drive unit.

Notes:

• Do not apply more tension to the belt of

the main motor drive unit than that pro-
duced by the spring force.

• Follow the procedure bellow to perform

tension adjustment when assembling the
main motor drive unit.
- Align the tensioner with the punch

mark and tighten the tensioner fixing
screw.

- Hook the tensioner spring.
- Install the main motor drive unit to the

equipment.

- Loosen the tensioner fixing screw.
- Let the spring force produce tension

for the belt, and tighten the fixing
screw.

Fig. 9-10

Fig. 9-11

Gear

Timing belt

Main motor drive unit

Tensioner spring

Tensioner

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 143 / 268

Search results

Summary of Contents for e-studio 167

Reviews: