Toshiba e-studio 167 Service Manual Download Page 187

Page: 187 / 268

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 15

[J] Drum separation finger

[K] Recovery blade

(1) Take off the drum.

P.11-14 "[H] Drum"

(2) Take off 2 drum separation finger units by

removing 1 screw each.

Note:

When replacing the drum separation fingers,
make sure that the drum has been taken off
first since the fingers may scratch the drum
surface.

Fig. 11-22

(3) Take off the drum separation finger with the

spring.

Note:

When the drum separation fingers have been
replaced, check if the pressure movement is
normal by moving them with your hands.

Fig. 11-23

(1) Take off 2 drum separation finger units.

P.11-15 "[J] Drum separation finger"

(2) Remove 2 screws, and take off the whole

recovery blade with the bracket.

Fig. 11-24

Drum separation finger unit

Drum separation finger

Spring

Recovery blade

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 187 / 268

Search results

Summary of Contents for e-studio 167

Reviews: