manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 239 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 239

14

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

AUTOMATIC DUPLEXING UNIT (ADU) (OPTION: MD-0103)

14 - 1

14. AUTOMATIC DUPLEXING UNIT (ADU) (OPTION: MD-0103)

14.1 General Description

The Automatic Duplexing Unit (ADU) is a unit to reverse a sheet of paper at duplex copying.
A switchback method using the exit roller is adopted for the ADU of this equipment. Immediately after
the printing of one side (fusing process) is completed, the paper is switchbacked by the exit roller. The
paper being reversed is then transported to the registration roller for the printing of the other side.
The ADU mainly consists of the transport rollers and their drive section, the paper guides and the ADU 
driving PC board (ADU).

 Fig. 14-1

Exit motor

Exit roller

ADU motor

Upper transport roller

ADU sensor

Lower transport roller

ADU driving PC board

Paper guide

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments