manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 93 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 93

6

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

SCANNER

6 - 1

6. SCANNER

6.1

General Description

In the scanning section, this equipment uses a CIS (Contact Image Sensor) for scanning the image. 
The surface of an original is irradiated with light from the LED array mounted on the CIS unit and the 
reflected light is scanned by the CCD where the optical image data are converted into an analog electri-
cal signal, and then transmitted to the MAIN board. After the binarization and the various image pro-
cessing operations necessary for image formation are performed on the MAIN board, the data are 
transmitted to the writing section.

 Fig. 6-1

Original glass

ADF original glass

Scan motor

CIS home position sensor

CIS unit

Original glass

ADF original glass

Scan motor

CIS home position sensor

CIS unit

Damp heater

Damp heater

Automatic original detection sensor 

Automatic original detection sensor 

Damp heater

Damp heater

Automatic original detection sensor 

Automatic original detection sensor 

LT series

A4 series

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments