Toshiba e-studio 167 Service Manual Download Page 185

Page: 185 / 268

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 13

[F] Main charger cleaner

[G] Needle electrode

(1) Take off the main charger.

P.11-12 "[D] Main charger"

(2) Release the hook of the cleaning shaft. Then

rotate the shaft at 90 degrees to take it off.

Fig. 11-17

(1) Take off the main charger grid and main

charger cleaner.

P.11-12 "[E] Main charger grid"
P.11-13 "[F] Main charger cleaner"

(2) Take off the terminal covers of both front and

rear sides.

Fig. 11-18

(3) Remove the terminal and spring. Then take

off the needle electrode.

Notes:

1. Do not touch the needle electrode directly

with bare hands.

2. Make sure not to hold or bend the needle

electrode.

Fig. 11-19

Main charger cleaner

Terminal cover

Needle electrode

Terminal

Spring

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 185 / 268

Search results

Summary of Contents for e-studio 167

Reviews: