Toshiba e-studio 167 Service Manual Download Page 40

Page: 40 / 268

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 24

[B] SRAM board (SRAM)

[C] Fuse PC board (FUS)

Note:

This fuse PC board is copacked with the damp heater unit. (The damp heater unit is optional for
NAD, CND and MJD.)

(1) Take off the rear cover.

P.2-22 "[J] Rear cover"

(2) Release 1 lock support and take off the

SRAM board.

Notes:

1. Be sure to perform “08-388” after the

SRAM board has been replaced.

2. Perform "05-310" with the platen cover

and the ADF/RADF closed after replacing
the SRAM board.

3. Make sure that the direction of the battery

on the SRAM board is correct when
replacing it.

Fig. 2-25

Fig. 2-26

(1) Take off the rear cover.

P.2-22 "[J] Rear cover"

(2) Remove 2 screws and take off the cover.

Fig. 2-27

SRAM board

Battery

Cover

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 40 / 268

Search results

Summary of Contents for e-studio 167

Reviews: