Toshiba e-studio 167 Service Manual Download Page 67

Page: 67 / 268

e-STUDIO167/207/237

COPY PROCESS

3 - 13

3.3

Comparison with e-STUDIO230/280

Process

e-STUDIO230/280

e-STUDIO167/207/237

1. Photoconductive drum

•

Sensitivity

•

Surface potential

OD-1600 (OPC ø30)

Highly sensitized/durable drum

-475 V

-440 V

2. Charging

•

Grid voltage

Scorotron method

-495 V

-448 V (e-STUDIO167/207)

-454 V (e-STUDIO237)

3. Data writing

•

Light source

•

Light amount

Semiconductor laser

(Adjustment not required)
4.0 nJ/mm

4. Development

•

Magnetic roller

•

Auto-toner

•

Toner supply

•

Toner-empty detection

•

Toner

•

Developer material

•

Developer bias

One magnetic roller

Magnetic bridge-circuit method

Toner cartridge

Density detection method

T-2320, T-2320E, T-2320D, T-2320C,

T-2320T

D-2320, D-2320C

DC-357 V Adjustable output

(during printing)

AC 1100 V (Adjustment not required,

during printing)

DC+150 V Fixed (others)

T-1640, T-1640E, T-1640D

T-1640C, T-1640T

DC -340 V Adjustment output (during

printing)

AC 1100 V (Adjustment not required,

during printing)

No DC+ (positive) output

5. Transfer

•

Transfer bias

Adjustable output (Constant current)

+600 V (Adjustment not required)

+565 V (Adjustment not required)

6. Separation

Adjustable output

(Constant current)

7. Discharge

•

Discharging position

•

Discharge LED

Exposure after cleaning

Red LED

8. Cleaning

•

Method

•

Recovered toner

Cleaning blade

Reuse (There is the recovered toner

supply mechanism.)

9. Fusing

•

Method

•

Cleaning

•

Heater

Long-life fuser roller method

Fuser roller:

Thin roller coated with fluoroplastic

(ø30)

Pressure roller:

PFA tube roller (ø30)

Cleaning roller for pressure roller (ø16)

Heater lamp

Turned ON/OFF by thermistor

Pressure roller:

PFA tube roller (ø25)

None

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 67 / 268

Search results

Summary of Contents for e-studio 167

Reviews: