manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 206 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 206

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

DEVELOPMENT SYSTEM

12 - 12

[B] Developer material 

(1) Take out the developer unit 

 P.12-11 "[A] Developer unit".

(2) Remove 2 screws and slide the developer 

unit upper cover to the direction of the arrow 
and take it off.

 Fig. 12-8

Note: 

When installing the developer unit upper 
cover, make sure that the side seal comes 
between the developer unit upper cover and 
rubber seal on the cover.

 Fig. 12-9

(3) Remove the developer material from rear 

side.

Note: 

When removing the developer material, be 
careful not to drop the developer material on 
the gears of the developer unit.

 Fig. 12-10

Developer unit upper cover

Side seal

Rubber seal

Developer unit 
upper cover

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments