Toshiba e-studio 167 Service Manual Download Page 184

Page: 184 / 268

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 12

[D] Main charger

[E] Main charger grid

(3) Release the harness from the harness clamp

and pull out the discharge LED.

Fig. 11-14

(1) Take off the discharge LED unit.

P.11-11 "[C] Discharge LED (ERS)"

(2) Pull out the main charger and take it off by

sliding it to the rear side.

Note:

Be careful not to touch or scratch the drum
surface at this time.

Fig. 11-15

(1) Take off the main charger.

P.11-12 "[D] Main charger"

(2) Remove the spring and take off the main

charger grid.

Note:

Do not touch the mesh area of the grid.

Fig. 11-16

Discharge LED

Main charger

Main charger grid

Spring

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 184 / 268

Search results

Summary of Contents for e-studio 167

Reviews: