Toshiba e-studio 167 Service Manual Download Page 37

Page: 37 / 268

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 21

[G] ADU cover

[H] Right front cover

(1) Open the bypass tray.
(2) Open the ADU cover.
(3) Open the transfer unit and release the ADU

stopper on the front side.

(4) Remove 1 screw and take off the ADU stop-

per on the rear side.

Note:

Be careful not to fall off the ADU cover when
the screws are removed from the ADU stop-
per.

Fig. 2-18

(5) Take off the ADU cover while sliding it toward

the right.

Fig. 2-19

(1) Take off the front cover.

P.2-18 "[A] Front cover"

(2) Open the ADU cover.
(3) Pull out the drawer.
(4) Remove 2 screws and take off the right front

cover.

Fig. 2-20

ADU stopper

ADU cover

Right front cover

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 37 / 268

Search results

Summary of Contents for e-studio 167

Reviews: