manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 234 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 234

e-STUDIO167/207/237

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

FUSER / EXIT UNIT

13 - 18

[G] Fuser roller 

(3) Pull out the center heater lamp and side 

heater lamp.

Notes: 

• When installing the heater lamps, be sure 

not to mix up the upper heater lamp and 
the lower heater lamp.
The upper heater lamp has a coil wound 
up on its center part, and the lower heater 
lamp has coils wound up on its both 
edges. 

• When installing the heater lamps, be sure 

to face up their weld sides. 

• Do not touch the lamps directly with your 

hands.

• The connector on each end of the har-

ness which connects to the center heater 
lamp has a small screw hole. The con-
nector on each end of the harness which 
connects to the side heater lamp has a 
big one.

 Fig. 13-23

 Fig. 13-24

(1) Take off the center heater lamp and the side 

heater lamp.

 P.13-17 "[F] Center heater lamp / Side 

heater lamp (LAMP1/LAMP2)"

(2) Take off the separation fingers.

 P.13-16 "[E] Separation finger"

(3) Take out the fuser roller upward. 

Notes: 

• When installing the fuser roller, slide each 

bushing on both edges of the roller out-
ward so that the bushings will engage 
with the frame and the installation will be 
secured.

• Do not apply force onto the roller because 

it may be deformed.

 Fig. 13-25

Center heater lamp

Side heater lamp

Upper side : center heater lamp

Lower side : side heater lamp

Weld

Fuser roller

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments