manualshive.com logo in svg

Toshiba e-studio 167, Service Manual, Page: 135 / 268

Share
Download
Toshiba e-studio 167 Service Manual Download Page 135

9

© 2007 - 2008 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO167/207/237

DRIVE UNIT

9 - 1

9. DRIVE UNIT

9.1

General Description

The main motor drives the drum, developer unit, cleaner unit, fuser unit and transport rollers which 
transport paper (bypass feed roller, bypass pickup roller, registration roller and pickup roller).
The main motor (M3) is a brushless motor and is installed in the drive unit. The drive unit consists of 
gears and timing belts, and transmits the driving force of the main motor (M3) to each unit. The toner 
motor (M2) which drives the toner cartridge is also installed in the drive unit. 
The exit roller is driven by the main motor (M3). However, when the automatic duplexing unit (ADU: 
optional) is installed, it is driven by the exit motor (M7).

 Fig. 9-1

Exit roller

Exit motor

Fuser roller

Toner recovery auger

Drum

Drive unit

Bypass feed roller

Bypass pickup roller

PFU drive gear

Pickup roller

Main motor

Mixer

Toner motor

Summary of Contents for e-studio 167













































































































































































































































































Reviews:

No comments