Toshiba e-studio 167 Service Manual Download Page 30

Page: 30 / 268

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 14

7) Thermistors and thermostats

8) Others

Symbol

Name

Function

Remarks

P-I

THMS1 THMS-C-HTR

Center thermistor

Detecting the surface temperature at

the center of the fuser roller (for con-

trolling the center heater lamp)

Fig. 2-5

23-6

THMS2 THMS-S-HTR

Side thermistor

Detecting the surface temperature at

the rear side of the fuser roller (for con-

trolling the side heater lamp)

Fig. 2-5

23-6

THMS3 THMS-EDG-HTR

Edge thermistor

Detecting the surface temperature at

the edge of the rear side of the fuser

roller (for preventing overheating)

Fig. 2-5

23-6

THMS4 THMS-DRM

Drum thermistor

Detecting the temperature on the drum

surface

Fig. 2-6

21-49

THMO1 THERMO-FSR

Fuser thermostat

Preventing overheating in the fuser unit

Fig. 2-5

23-5

THMO2 THERMO-SCN-DH

Scanner damp heater thermostat

Preventing overheating in the scanner

damp heater

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-3

9-20

THMO3 THERMO-DRM-DH

Drum damp heater thermostat

Preventing overheating in the drum

damp heater

Optional for NAD/MJD/CND model,

standard for other models

Fig. 2-6

8-7

Symbol

Name

Function

Remarks

P-I

CIS

Contact image sensor unit

Reading originals

Fig. 2-3

9-8

PS-ACC

Switching regulator

•

Generating DC voltage and supply-

ing it to each section of the equip-

ment

•

Generating high voltage and sup-

plying it to the main charger, devel-

oper, transfer and separation units

•

Supplying AC power to the heater

lamp

Fig. 2-4

5-2

LCD

LCD panel

Displaying each information

Fig. 2-3

4-19

Summary of Contents for e-studio 167

























































































































































































































































Search results

Summary of Contents for e-studio 167

Reviews:

Toshiba e-studio 167, Service Manual, Page: 30 / 268

Search results

Summary of Contents for e-studio 167

Reviews: