Thrane&Thrane Explorer 727 User Manual Download Page 136

Page: 136 / 148

Appendix 5: Troubleshooting

98-126882-B

Status signaling

128

08032

Firmware image
version lower
than active
antenna
version

The firmware in the
antenna is newer than
expected by the terminal.

Update the terminal
software.

08033

Firmware image
doesn't
support
antenna
hardware

The antenna hardware
version is not supported by
the terminal.

Contact your distributor.

08034

Antenna failed
to exit Flash
Manager. Power
cycle needed

New firmware was
successfully uploaded to
the antenna but the
antenna failed to start
normally with the new
firmware.

Reboot the terminal.
Contact your distributor if
the problem persists.

08035

Unable to open
port for HPA
burst
monitoring

There was an error
communicating with the
antenna.

Reboot the terminal.
Contact your distributor if
the problem persists.

08036

Radio silence
is activated

The Radio silence function
is activated. No
transmission is allowed.

If the Radio silence
function should not be
active, enter the web
interface and select

SETTINGS > Discrete I/O

Then uncheck the

Enabled

box for

Radio silence

Event Text

Explanation

Remedy

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands