Thrane&Thrane Explorer 727 User Manual Download Page 56

Page: 56 / 148

Chapter 4: Using the web interface

98-126882-B

Using the Dashboard

Viewing information on calls and data sessions

The following sections in the

Dashboard

show information on calls and data sessions.

•

ONGOING CALLS

is a list of calls that are currently active. The list shows the call type and the

time connected for each call.

•

ONGOING DATA SESSIONS

is a list of data profiles that are currently active, including the IP

address that is assigned to each profile.

•

SESSIONS TOTAL

lists the totals for each connection. The list shows the time connected for

voice and Streaming data, and MB transferred for Standard data.

The counters show totals for connections since the counters were last cleared.

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands