Thrane&Thrane Explorer 727 User Manual Download Page 67

Page: 67 / 148

Chapter 4: Using the web interface

98-126882-B

Handling SMS messages

Viewing or changing SMS service center number

The SMS service center number identifies the SMS service center used when sending and
receiving SMS messages. The SMS service center number is stored on the SIM card.

•

To see the SMS service center number, select

MESSAGES

Message settings

from the left navigation pane.

•

To change the number, click

Edit

next to

SMS service center

, change the number and click

Save

. Then click

Apply

to apply all changes in the page.

The SMS service center number is provided from your Airtime Provider.

Viewing the Voice mail number

The Voice mail number is the number you call to hear your incoming voice mails.

To see the Voice mail number, select

MESSAGES

Message settings

from the left navigation pane. The

Voice mail number

field shows

the Voice mail number.

Note

The Voice mail number is only listed if it is available on the SIM card. Otherwise, refer to
the information included with your Airtime subscription.

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands