Thrane&Thrane Explorer 727 User Manual Download Page 20

Page: 20 / 148

98-126882-B

In this chapter

Chapter 2

Getting started

In this chapter

This chapter describes how to start up the system and make the first call or data session.

For information on how to install the system, insert SIM card and connect cables, refer to the
installation manual for the EXPLORER 727 system

Before you start

Operation at high temperatures

In very high ambient temperatures, do not touch areas of the terminal that are
marked with this symbol.

If the terminal is installed in a location where the ambient temperature may rise above 50

C, we

recommend placing the terminal where unintentional contact is avoided. Note that the maximum
allowed ambient temperature is 55° C.

If the maximum ambient temperature does not exceed 50

C, the terminal can be placed in a public

area.

For further information on installation, refer to the installation manual for the EXPLORER 727
system.

Connector panel

The drawing below shows the connector panel of the terminal.

For information on how to connect to each interface, refer to the installation manual for the
EXPLORER 727 system.

Grounding stud

Power
switch

I/O

DC input

4 x LAN w. PoE

SIM slot

ISDN

Phone 1

Antenna

Reset button

Phone 2

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands