Thrane&Thrane Explorer 727 User Manual Download Page 49

Page: 49 / 148

Chapter 4: Using the web interface

98-126882-B

Introduction

Accessing and navigating the web interface

Accessing the web interface

To access the web interface, do as follows:

Connect your computer to the terminal.

Start up the terminal.
For further information, see

Getting started

on page 12.

Open your browser and enter the IP address of the terminal.
The standard IP address is

192.168.0.1

Note

If the IP address is changed and you do not have the new address, you can temporarily
set the IP address to the default value by pressing the

Reset

button next to the SIM slot in

the connector panel of the terminal. You can then access the web interface and change
the IP address.

Note that if you do not change the IP address, the default IP address will only be valid
until the terminal is powered off. Then the terminal returns to the IP address from before
the Reset button was pressed.

For further information on the Reset button, see

Reset button

on page 130.

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands