Thrane&Thrane Explorer 727 User Manual Download Page 139 | Manualshive

Page: 139 / 148

background image

98-126882-B

EXPLORER

®

727

131

Chapter 6

Conformity

6

EXPLORER

®

727

CE (R&TTE)

The EXPLORER 727 is in the process of being CE certified (R&TTE directive). The “Declaration of
Conformity with R&TTE Directive” will be enclosed in copy on the next page when ready.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1) This device may not cause harmful interference, and

2) this device must accept any interference received, including interference that may cause
undesired operation.

Part 15.21

Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

Note

The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's
authority to operate the equipment.

«
...
137
138
139
140
141
...
»

Summary of Contents for Explorer 727





















































































































































Reviews:

No comments

Related manuals for Explorer 727

Brand: Panorama Antennas Pages: 2

Brand: M2 Antenna Systems Pages: 8

Brand: H3C Pages: 6

Brand: Chameleon Antenna Pages: 24

Brand: LAPLACE INSTRUMENTS Pages: 11

Brand: SureCall Pages: 1

Brand: TERK Technologies Pages: 6

Brand: Antsig Pages: 2

Brand: CUSHCRAFT Pages: 7

Brand: Televes Pages: 4

Brand: Televes Pages: 4

Brand: I0JXX Pages: 4

Brand: GIGA-TMS Pages: 21

Brand: NUXCOM Pages: 2

Brand: M2 Antenna Systems Pages: 10

Brand: Tarheel Antennas Pages: 9

Brand: Tarheel Antennas Pages: 7

SquareShooter HDTV2 SS-2000

Brand: Winegard Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands