Thrane&Thrane Explorer 727 User Manual Download Page 127

Page: 127 / 148

Appendix 5: Troubleshooting

98-126882-B

Status signaling

119

Status signaling

Overview

There are many ways of troubleshooting if an error occurs. The terminal has different means of
status signaling, to help you find the cause of a problem:

•

Indicators

•

Event messages.

•

Event log.

Indicators, event messages and logs are described in the following sections.

Light indicators

Overview

The terminal has a number of LEDs, placed in the panel at the top of the terminal:

•

a green Power indicator,

•

a green/red/ orange Terminal indicator,

•

a green/red/orange Antenna indicator,

•

a green Message indicator and

•

3 LAN indicators for each LAN interface, showing Activity (Green), Link/Speed (Green/Yellow)
and PoE (Green/Red).

General status indicator functions

Summary of Contents for Explorer 727





















































































































































Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands

Thrane&Thrane Explorer 727, User Manual

Search results

Summary of Contents for Explorer 727

Reviews:

Related manuals for Explorer 727

Brands by name

Popular brands