Thermo King TriPac Envidia Installation Manual Download Page 50

Page: 50 / 80

HMI Installation

HMI Controller Location

Choose a location inside the tractor’s sleeper for the HMI controller that is easily accessible and visible from
the driver’s bunk

Installation

Special Tools Required

Level

Drill Motor

Drill Bits

Locate the

HMI Controller Harness

with the

8-pin

connectors on each end supplied loose in the installation kit. The

connectors are not the same. Connect the white end to the HMI.

Route the harness to the Evaporator/Control Box.

Connect the black 8-pin connector to the HMI (J7) connector on the Evaporator/Control Box connector panel.

From the Evaporator/Control Box, route the harness behind the interior walls (if applicable) to the location chosen
to install the HMI controller.

Unsnap the rear mounting base from the controller and route the harness connector through the access hole.

Position and level the mounting base and install securely.

Push the white connector firmly into the plug on the rear of the controller.

Snap the controller back onto the mounting base.

Secure harness.

Figure 26: HMI Controller Installation

Summary of Contents for TriPac Envidia

















































































Search results

Summary of Contents for TriPac Envidia

Reviews:

Related manuals for TriPac Envidia

Brands by name

Popular brands

Thermo King TriPac Envidia, Installation Manual

Search results

Summary of Contents for TriPac Envidia

Reviews:

Related manuals for TriPac Envidia

Brands by name

Popular brands